Desa (V)T32EN-A SERIES Manual do Utilizador

DIRECT-VENT FIREPLACEOWNER’S OPERATION AND INSTALLATION MANUALSave this manual for future reference.For more information, visit www.desatech.comNATURA

www.desatech.com116647-01B106. Noncombustible Exterior Wall: Position the horizontal vent cap in the center of the 8 1/2" round hole and attach

www.desatech.com116647-01B 11Figure 13 - Typical Horizontal Termination Cap Mounting with Additional Siding Standoff InstalledSiding Standoff ScrewsHi

www.desatech.com116647-01B12VENTING INSTALLATION INSTRUCTIONSContinued Vertical (V) Required Vertical (V) Vertical Pipe Horizontal (H) *43 3/4

www.desatech.com116647-01B 13HORIZONTAL SYSTEM INSTALLATION USING TWO 90° ELBOWSThe following congurations show the minimum vertical rise requiremen

www.desatech.com116647-01B14INSTALLATION FOR VERTICAL TERMINATIONNote: Vertical restrictor must be installed in all vertical installations.1. Deter

www.desatech.com116647-01B 156. Continue to add pipe sections until the height of the vent cap meets the minimum building code requirements described

www.desatech.com116647-01B16VENTING INSTALLATION INSTRUCTIONSContinuedVertical VentingV = 40' max.Figure 24 - Vertical Venting Conguration With

www.desatech.com116647-01B 17VENTING INSTALLATION INSTRUCTIONSContinuedNumber DescriptionHHTK-58 High Wind Round Horizontal Termination Kit (I

www.desatech.com116647-01B183. Place the blower against the lower rear wall of the rebox outer wrapper with the exhaust port directed upward. The b

www.desatech.com116647-01B 193. Place the blower against the lower rear wall of the rebox outer wrapper with the exhaust port directed upward and t

www.desatech.com116647-01B2WARNING: Improper installation, adjustment, altera-tion, service or maintenance can cause injury or prop-erty damage. R

www.desatech.com116647-01B20INSTALLING GAS PIPING TO FIREPLACE LOCATION WARNING: A qualified service person must connect replace to gas supply.

www.desatech.com116647-01B 21IMPORTANT: Install main gas valve (equipment shutoff valve) in an accessible location. The main gas valve is for turning

www.desatech.com116647-01B22Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)1. Close equipment shutoff valve (see Figure 33).2. Pressurize s

www.desatech.com116647-01B 23Removing Glass DoorIf replacement of glass is necessary, the entire assembly, glass and frame, must be replace

www.desatech.com116647-01B246. Install left side brick panel by sliding it be-tween the grate and the side of the rebox (see Figure 39).7. Install

www.desatech.com116647-01B 254Figure 43 - Installing Log No. 456Figure 44 - Installing Logs No. 5 and No. 6FIREPLACE INSTALLATIONContinued8. Pull emb

www.desatech.com116647-01B26EV2EV1ORANGEIGNITOR LEADGREENPILOTTRANSFORMERIS1070BSYNETEK CONTROLS INC24V ACE4E2E3E6REDE8E12BLUE120V ACGROUNDBLACKWHITEW

www.desatech.com116647-01B 277. Turn equipment shutoff valve counter-clockwise to the ON position. Do not force.8. Close lower louver pane

www.desatech.com116647-01B28INSPECTING BURNERSCheck pilot ame pattern and burner ame pat-terns often.PILOT ASSEMbLYThe pilot assembly is factory pre

www.desatech.com116647-01B 29CLEANING AND MAINTENANCEContinued WARNING: Only parts sup-plied by the manufacturer should be used when replacing broken

www.desatech.com116647-01B 3 DANGER: Carbon monoxide poisoning may lead to death!This replace must be installed by a qualied (cer-tied or licensed)

www.desatech.com116647-01B30TROUBLESHOOTING WARNING: Turn off heater and let cool before servicing. Only a qualied service person should service and

www.desatech.com116647-01B 31TROUBLESHOOTING ContinuedPOSSIBLE CAUSE1. Wall switch wires defective or too long1. Pilot ame may be too low, cau

www.desatech.com116647-01B32SPECIFICATIONS(V)T32EN(R)-A• Rating: 12/18,000Btu/Hr• Type Gas: Natural Gas Only• Ignition: Piezo• Manifold Pressure:

www.desatech.com116647-01B 33ACCESSORIESNOTICE: All accessories may not be available for all replace models.Purchase these replace accessories fr

www.desatech.com116647-01B34ILLUSTRATED PARTS BREAKDOWNMODELS (V)T32EN-A, (V)T32ENB-A, (V)T32ENR-A, (V)T32ENRB-A, (V)T32EP-A, (V)T32EPB-A, (V)T32EPR-A

www.desatech.com116647-01B 35PARTS LISTThis list contains replaceable parts used in your replace. When ordering parts, follow the instructions listed

www.desatech.com116647-01B36IGNPVGNDPV/MVTRTHMV2123242625271722161420129810131519182829112173546ILLUSTRATED PARTS BREAKDOWNBURNER ASSEMBLY MODELS (V)T

www.desatech.com116647-01B 37KEYNO. PART NO. DESCRIPTION QTY.1 11102 Screw #8-32 x 3/8 PPH Zinc 22 11105 Screw #10 x 1/2 Zinc 93 108886-01 Base Grate

www.desatech.com116647-01B38__________________________________________________________________________________________________________________________

www.desatech.com116647-01B 39_________________________________________________________________________________________________________________________

www.desatech.com116647-01B4SAFETY INFORMATIONContinued6. Turn replace off and let cool before servicing, installing or repairing. Only a qualied se

116647 01116647-01Rev. B11/05NOT A UPCLIMITED WARRANTYDIRECT-VENT FIREPLACEDESA warrants this product to be free from defects in materials and compone

www.desatech.com116647-01B 5PRE-INSTALLATION PREPARATIONLOCATION AND SPACE REqUIREMENTSDetermine the safest and most efcient location for your DESA d

www.desatech.com116647-01B6PRE-INSTALLATION PREPARATIONContinuedNOTICE: This replace is in-tended for use as supplemental heat. Use this repl

www.desatech.com116647-01B 7FixedClosedOpenableFixedClosedOpenableVVVVVVVVXXVXGGJFBBKNHIANELDBMACBVVAGGBTERMINATION CAPAIR SUPPLY INLETGAS METER RESTR

www.desatech.com116647-01B8VENTING INSTALLATION INSTRUCTIONSNOTICE: Read these instruc-tions completely before at-tempting installation.These m

www.desatech.com116647-01B 9INSTALLATION PLANNINGThere are two basic types of direct-vent instal-lation:• Horizontal Termination• Vertical Te